Is a wind turbine vent the right answer for your attic, or would another kind of vent serve you better? This guide takes the 12-inch mill aluminum externally braced model as its example and looks at the practical side: how to look after a turbine vent, what goes wrong with one, and when a turbine vent is simply the wrong choice for a roof.
What a Mill Aluminum Turbine Vent Is
A wind turbine vent, often called a whirlybird, is a round metal head that spins on top of a roof and draws air out of the attic. The head is made of curved fins that catch the wind. As it turns, it pulls warm, damp air up out of the attic through a pipe in the roof. It has no motor and uses no power. The wind does the work, and when the air is still, warm air still drifts out through the head on its own, because warm air rises toward the highest opening it can find.
Mill aluminum means aluminum in its natural state, with no paint or coating applied. It leaves the mill as bare metal, and that is how it goes onto the roof. The surface is a bright silver-gray when new, and it weathers over time to a softer, duller gray. That change in appearance is normal for bare aluminum, and it does not mean the metal is failing. Aluminum does not rust the way steel does. It forms a thin oxide layer on its surface that protects the metal underneath, and that layer is the reason bare aluminum can sit on a roof for years without a coating.
The 12-inch size refers to the diameter of the spinning head. A 12-inch turbine is a common size for a single-family home, and it suits a roof of ordinary size when the attic also has enough intake ventilation low on the roof or under the eaves. A larger attic may need more than one turbine, spaced across the roof so the air moves through the whole space. The number of vents and their placement matter more than the size of any one vent.
External Bracing and What It Changes
The head of a turbine vent is made of thin metal fins, and those fins need a frame to hold them in shape. In an externally braced design, the frame sits on the outside of the head, where you can see it. Bands or straps run around the head and across the fins, holding them in place and keeping the head round. The bracing is visible, and it gives the vent a different look from a model whose frame is hidden inside. Some homeowners like the look, and some do not, so it is worth looking at a photo of the vent before you buy.
The visible frame has practical effects too. External straps give the head extra stiffness, which helps it hold its shape in strong wind. A head that keeps its round shape spins true on its spindle, and a head that spins true puts less strain on its bearings. The trade-off is that the straps give wind-blown leaves, snow, and ice more to catch on. In a place with heavy, wet snow, an externally braced head can collect more snow on its frame than a smooth-headed vent would, and a head weighed down with snow or ice may turn slowly or stop until the snow clears. In a mild climate that trade-off hardly matters, but in a snowy one it is worth thinking about.
The bearings are the moving heart of the vent, and they sit at the center of the head on the spindle. They let the head turn in a light breeze, and they decide how much wind the vent needs before it starts working. Sealed bearings keep dust and moisture out and need little care. Bearings that are not sealed can dry out, and a turbine with dry bearings turns slowly or not at all. When you handle a turbine vent, spin the head by hand. It should turn smoothly and quietly, with no wobble and no scraping. A head that wobbles before installation will wobble worse on the roof.
Looking After a Turbine Vent Year by Year
A turbine vent needs little care, but it does need some. Once a year, look at the vent from the ground with binoculars, or ask a roofer to check it during a roof inspection. Watch it on a breezy day. A head that turns freely is working. A head that sits still while the wind blows is not, and the cause is usually dry bearings, a bent head, or debris caught in the fins. A head that squeaks or rattles is telling you the bearings need attention. Some vents have bearings that can be oiled, and some have sealed bearings that must be replaced when they wear out. Find out which type yours has before you need to know.
Check the finish at the same time. Mill aluminum weathers to a dull gray, and that is normal, but look for white, chalky patches or pitting, which can mean the metal is corroding in a harsh environment. Near the coast, salt air is harder on bare aluminum than inland air, and a coated vent may hold up better there. If the vent is painted later, the surface must be cleaned and primed with a primer made for aluminum, because paint does not stick well to bare metal without preparation. If you want a colored vent, it is simpler to buy one with a factory finish than to paint a mill-finish vent on the roof.
Look at the flashing where the vent joins the roof. Watch for sealant that has split or come away, shingles that have curled up around the base, and any water marks on the underside of the roof deck close to the vent. A minor flashing fault costs little to put right when it is spotted early. Ignored, it can drip for a whole season before anyone notices from inside. Inspect the outside bracing as well. The straps should sit tight and firm, with no loose fixings and no bent lengths. A strap that has shaken loose can rattle in the wind and wear the fins where it rubs against them.
If the head stops turning and the bearings cannot be freed, a new head can usually be fitted without taking the flashing base off, which keeps the task simple and the roof whole. Ask the seller whether spare heads are sold for the model you buy, and file the model details with the roof records. A turbine vent that gets a yearly look and a little attention when it asks for it will keep an attic ventilated for many years.
Common Problems and What Causes Them
A turbine vent that will not spin is the most common complaint, and the cause is almost always the bearings. Dust, moisture, and time dry them out or corrode them. If the bearings can be oiled, a few drops of light oil may free them, but oil is a short-term fix for a bearing that is already worn. A bearing that has rusted solid will not come back with oil, and the head or the bearing assembly needs replacing. Do not force a stuck head to turn by hand with a hard push, because you can bend the fins or the spindle and make the problem worse.
Noise is the next most common complaint. A turbine vent should be nearly silent. A squeak usually means dry bearings. A rattle usually means a loose fastener, a bent fin, or a strap that has worked loose. A rhythmic thumping can mean the head is out of balance because a fin is bent or dented. Find the cause before the noise gets worse, because a vent that rattles is wearing itself out. A bent fin can sometimes be straightened by hand with the power of patience and a gentle touch, but a fin that is creased or cracked should not be forced back into shape, because it will crack further.
A leak around the base of the vent is a flashing problem, not a turbine problem. The flashing must shed water correctly, with the shingles lapped over its top edge and the sides sealed. If the sealant has failed or the flashing was fitted badly, rain can run under it and into the attic. A leak that appears only in wind-driven rain points to the flashing or to the seal around the pipe. A leak that appears in every rain points to a bigger gap. Either way, the fix is roofing work, and it should be done by someone who knows flashing. Do not try to stop a roof leak by sealing the turbine head itself, because that blocks the ventilation the vent is there to provide.
When a Turbine Vent Is the Wrong Choice
A turbine vent is a good tool for many roofs, but it is not the right tool for every roof. If your attic has no intake ventilation, a turbine vent will not move much air, because air cannot leave the attic unless fresh air can enter. An attic with no soffit vents, no gable vents, and no other intake is a poor candidate for a turbine vent until the intake side is fixed. A contractor who suggests adding a turbine without looking at the intake vents is selling you half a system.
A roof in a place with long, icy winters is another poor fit. A turbine head can freeze in place during an ice storm, and a head packed with snow may not turn until the snow melts. In that climate, a static vent that cannot freeze shut, or a powered vent with a thermostat, may serve the attic better through the winter. A roof that gets very little wind is a poor fit too. A turbine vent in a sheltered hollow, behind a taller building, or under a dense tree canopy may sit still for days at a time, and a still turbine moves far less air than a ridge vent or a static vent of the same size.
A roof with a powered attic fan already installed is a third case to think about. A powered fan can pull air backward through a turbine vent, which wastes the fan power and can pull rain into the attic through the turbine. If your attic already has a powered fan, ask a contractor whether adding a turbine helps or hurts before you cut another hole in the roof. The same caution applies to a ridge vent. A ridge vent and a turbine vent on the same attic can short-circuit each other, with air entering through one exhaust vent and leaving through the other instead of traveling up through the attic from the intake vents.
Aesthetics matter too, and they are a fair reason to choose differently. A turbine vent is visible on the roof, and some homeowners do not like the look of a spinning metal ball, especially on the front slope of a house. If the vent would sit on the street-facing slope, consider whether a low-profile static vent or a ridge vent would do the same job with less visual impact. A turbine vent on the rear slope is far less noticeable, and that is where most of them are installed.
Questions to Ask a Roofing Contractor
Ask the contractor to look at the whole attic ventilation system before recommending a turbine vent. Ask whether the attic has enough intake ventilation, how many exhaust vents the attic needs, and whether a turbine vent is the right type for your roof and your climate. Ask where the vent would sit, and whether that spot gets enough wind. Ask whether the vent comes with a flashing base that fits your roof type and pitch, and what the base is made of.
Ask about the bearings and the maintenance they need, and whether replacement heads are available for the model you buy. Ask how the mill aluminum finish will weather on your roof, and whether a coated vent would suit your climate better, especially if you live near the coast. Ask what the installed cost will be, including the flashing, the sealing, and any repair to the roof covering around the vent. Ask what the warranty covers. A turbine vent is a small purchase, but the roofing work around it is what keeps your roof dry, so a clear quote and a clear plan up front save surprises later.