Most gable vents are made to disappear. A cedar wood louver vent is made to be seen. It is the vent you choose when the gable end is part of the look of the house: a craftsman bungalow, a cottage with shingle siding, a farmhouse with painted trim. This guide looks at a 16-inch by 24-inch cedar wood rectangular louver vent: what cedar brings to an outdoor vent, how the louvers work, and how to fit, finish, and care for a wood vent so it stays sound for years.
A louver vent is a vent covered by angled slats, called louvers, that let air pass while blocking rain. On a gable vent, the louvers sit in a rectangular frame that mounts on the outside of the gable end wall, over an opening cut into the wall. Air from the attic flows out between the slats. Rain running down the wall hits the angled slats and runs off instead of blowing into the attic. Behind the louvers there is usually a screen that keeps insects and small animals out while letting air through.
Why cedar
Cedar is a softwood with a long history in outdoor building. It is light, easy to cut and shape, and it holds up outdoors better than many other softwoods. Cedar heartwood contains natural oils that resist rot and insects, which is why it has been used for shingles, siding, and outdoor trim for generations. A cedar vent does not need to be painted to survive outside, though it will weather to a silver-gray color if it is left unfinished and exposed to sun and rain.
Cedar also takes a finish well. It accepts stain, oil, and paint, and it holds them better than some harder woods because its surface is open and even. That matters for a vent that needs to match the house. You can stain a cedar vent to blend with cedar shingles, or paint it to match the trim color, and the finish will sit well on the wood. If the house trim changes color later, the vent can be stripped and refinished rather than replaced.
The trade-off is that cedar is softer than hardwood and softer than the metal or vinyl used for most vents. It can dent if it is hit, and it can crack if it is fastened badly or left to dry out unevenly. A cedar vent needs a little more care than a metal one, and it repays that care with a look that metal and vinyl cannot match.
What 16 by 24 inches means for your wall
Sixteen by twenty-four inches is the size of the finished vent: the frame, the louvers, and the edge you see from the street. The hole cut into the gable wall is smaller than that, because the frame is meant to lap over the edges of the hole and screw down onto the wall around it. If you are swapping out an old vent, start by measuring the hole already in the wall, then compare it with the new vent's frame and its opening size. You want the frame to cover the hole with room to spare on each side, so the vent seals against sound wall and not against fresh air.
A 16 by 24 inch vent is a generous size for a gable end, and it suits a larger gable or a house where the vent is meant to be a visible feature. The rectangular shape is longer than it is tall, which fits the wide, low triangle of many gable ends better than a square vent would. Center it on the gable, or align it with the windows below, so it looks like it belongs there rather than stuck on as an afterthought.
Think about the attic behind the vent, too. A vent this size moves a good amount of air, but only if the air behind it is free to move. Check from inside the attic that insulation is not piled against the back of the vent, and that the opening in the wall is clear. A vent blocked from behind is a decoration, not ventilation.
Finishing cedar before it goes on the wall
Finish a cedar vent before you install it, not after. It is far easier to stain or paint every surface, including the back and the edges, while the vent is on a workbench. The back and edges are the parts most exposed to moisture from inside the attic, and sealing them is what keeps the wood from swelling and cracking.
Choose a finish made for exterior wood. A penetrating oil or stain soaks into cedar and lets the grain show through, which suits a natural look. A solid stain or an exterior paint covers the grain and matches painted trim. Whatever you choose, apply it to all six sides of the vent: front, back, top, bottom, and both ends. Pay attention to the end grain, the cut ends of the wood, since end grain soaks up water faster than the face of a board. A good coat on the end grain is the difference between a vent that stays tight and one that splits at the corners.
Let the finish dry fully before installation. A vent installed with wet paint will stick to the wall and mark the siding. If you are painting the vent to match the trim, do a test patch first and look at it in daylight against the trim, since paint colors shift between the can and the wall.
Installing a wood louver vent
A cedar vent is installed much like any gable vent, with a few extra points that matter for wood. Start by test-fitting the vent over the opening. It should sit flat against the wall, with the frame overlapping the opening evenly. If the wall is uneven, shim behind the frame so it sits true and does not twist. A twisted frame will bind the louvers and stress the joints.
Fasten the vent with screws rather than nails. Screws hold better in cedar, they can be removed if the vent ever needs refinishing, and they are less likely to split the wood if you drill pilot holes first. Drill a pilot hole for each screw, sized just under the screw diameter, and use screws made for exterior use so they do not rust and stain the cedar. Stainless steel or coated deck screws are a good choice. Drive the screws snug but not so tight that they crush the wood fibers around the hole.
Seal the edges with exterior caulk rated for wood and for the siding material. A neat bead around the frame keeps rain from getting behind the vent and into the wall. Keep the caulk off the louvers themselves, since caulk in the slats blocks airflow and looks untidy. From inside the attic, check that the screen is in place behind the louvers and that daylight comes through freely.
Working on a gable end means working at height. If the vent is on a second story, use scaffolding or hire the work out rather than stretching from a ladder. A wood vent is not heavy, but fitting it well takes two hands and a steady position.
Keeping a cedar vent in good shape
A cedar vent asks for a little more attention than a metal one, and the attention is simple. Once a year, look at it from the ground and from inside the attic. Check the finish: if the stain or paint is peeling, flaking, or worn thin on the side that faces the weather, it is time to refinish. A vent left with bare wood exposed will still last for years, since cedar resists rot, but it will weather unevenly and may check and crack at the surface.
Check the louvers for cracks and the frame for gaps at the joints. Cedar moves with changes in humidity, swelling in damp weather and shrinking in dry weather, and that movement can open small gaps at the corners over time. A dab of exterior wood filler and a touch of finish will close a small gap. A louver that has cracked can usually be replaced without replacing the whole vent, if the vent was built with removable slats. Ask the maker or the supplier whether spare louvers are available.
Clean the vent with a soft brush and a rinse. Do not pressure-wash it at close range, since the force of the water can gouge soft cedar and drive water into the joints. Clear cobwebs and dust from the louvers so air flows freely, and check the screen behind them for holes. A torn screen is an open door for wasps and bats.
Airflow: what the vent needs around it
A louver vent lets warm attic air out, and that only works if fresh air can get in somewhere low. In most houses the fresh air comes through the soffits beneath the eaves, travels up the slope of the roof, and leaves through the gable vent. If the soffits are painted shut or buried under insulation, the vent has almost nothing to exhaust, and the attic stays hot no matter how large the vent is. Clear the soffits before you fit the vent, and keep insulation pulled back from the eaves.
One vent on each gable end gives the attic a through-draft whenever the wind runs along the house. One vent alone can still work, paired with a ridge vent or with generous soffit intake, but the airflow will be gentler. A roofer or contractor can judge whether your attic needs a second vent. Remember what the vent is for: it moves air out of the attic, and the rooms below feel the benefit only through the ceiling. Insulation above the ceiling and sealed gaps around pipes and wires do as much for comfort as the vent itself, and the three work well as a set.
Questions to ask before you buy
Ask the supplier what kind of cedar the vent is made from and whether the louvers are fixed or removable. Ask whether the vent comes finished or unfinished, and what finish the maker recommends for your climate. Ask whether a screen is included, and whether it is fixed behind the louvers or removable for cleaning.
Ask your contractor whether the opening in your wall matches the vent, and how the vent will be sealed and flashed. Ask whether your soffit vents are open, since a louver vent without intake air does little. And ask how the vent should be refinished, and how often, so you know what you are signing up for.
A 16 by 24 inch cedar wood rectangular louver vent is a vent that does two jobs at once: it lets the attic breathe, and it looks like it belongs on the house. It asks for a careful finish before installation, screws and pilot holes instead of rushed nailing, and a look once a year with a brush and a fresh coat when the finish wears thin. Give it that, and it will ventilate the attic and dress the gable end for many years.